9 Simple Steps to Waterproofing Exterior Walls


“The foundation of your home is built up by your walls. The weather out there will not be nice for the exterior walls of your house. It isn’t enough to paint your wall. After dealing with rain, snow, wind, dust, and the heat of the outside environment, the paint will begin to peel off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

A lot of dust and dirt is carried by air and sticks onto the outer part of the wall. To ensure the efficiency of the whole process, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned using a broom, brush, or sandpaper. Then rinse it off with a power washer.

Step 3: Check out for the cracks and fill them up

Cracks and holes can be found over time on your walls. Follow up the cleaning process with a thorough look at the cracks and holes on the wall to make sure proper weatherproofing is ensured. Just fill them up with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The mixture of cement penetrated inside the cracks. Make sure to remove all the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply the cement waterproofer. After applying the cement in the crevices, let it dry, then apply the waterproof paint seal for the walls. It should become dry after that.

Step 5: Pick the right water-proofer

There are many waterproof products available in the market. You have to pick the one that goes with the wall. Pick the water-proofer based on whether it is a concrete wall or a silicate one.

You can choose between a silicate-based concrete sealer and a concrete waterproofing coating. Pick a plaster waterproof Additive that will add strength to your walls.

Step 6: Apply the water-proofer

Apply the water-proofer with a roller or brush on the walls. If you want to apply more than one layer, you should give a thin coat. Let the first coat dry before adding the second.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layers, you need to use a tar-based pitch after the drying of the cement waterproofer. You can apply it on the exterior wall.

After that, you need to apply a heavy-duty plastic or rubber membrane for waterproofing, which will ensure the proper care of your walls.

Step 8: Consider adding gravel

To lay the drainage pipes, you need a base below the footer. The drainage pipes are going to get adequate support from a gravel base. Gravel is long- lasting and provides enhanced protection.

You need to lay the drainage pipe-cover and gravel. Next to the footer, level the position of the gravel and back-fill it. The pipe should be covered for at least three inches.

Step 9: Add a fabric barrier

Attach the pipe with a fabric barrier. The formation of dirt is prevented by a fabric barrier. Then back-fill the trench and build the top of the dirt relatively high and let it settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia


Good waterproof gives your home a new life and strength to deal with outside weather related issues. If you want good solutions for your walls, Magicrete is here to help. At a very low and affordable price, Magicrete offers you proper weatherproofing with quality service.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like”

Leave a Reply

Your email address will not be published. Required fields are marked *